Improve Your Understanding of How Emergency Power Systems Works

Electricity is something we are severely dependent upon so when the power goes out for more than a few minutes, it is easy to feel annoyed. However, with the help of an emergency power system all of this can be avoided. Here we take a look at how emergency power systems work to help you get a better understanding of what you need to meet your requirements.

Inverter or Generator
An easy way to provide emergency power to the house is by means of engine-powered generator. These are relatively inexpensive products and produce clean, 120- or 240-volt sine-wave power. The fuel consumption is also fairly low at around a gallon for every two hours. Diesel-fuel or propane-based generators are also available in the market.
Using a generator has a number of disadvantages as well, and these are highlighted as under:

• It is a nuisance to store the fuel
• They make a lot of noise
• The engine has high maintenance

An inverter is an electrical device where 12-volt power is converted into 120-volt power and typically runs off a deep-cycle battery that is bought to specifically power the inverter. It is an easy and inexpensive solution for low-wattage power demands. There are two main advantages to using an inverter:

• They operate silently
• They don’t require any maintenance except for the deep-cycle batteries

The conclusion that can be drawn from the above discussion is that an inverter is a good choice when the power load is very small and needs to be serviced over short time frames. It may be backed up by a large and elaborate battery system but the setup can become very expensive and may not be worth the investment.

Sure-fire Ways to Trace a Reliable UK Load Transfer Switch Dealer Online

A load transfer switch presents numerous functions and serves as an integral part of any emergency power backup system. Be it a standby or an easily portable generator, the switches serve as one of the crucial components for an interrupted power supply. That said, you should ensure the source of purchase is a countable one.

Here are some tips which could help you sort out the Good from the Substandard. Keep reading!

# The Dealers Must Have Transfer Switches Of Both Categories…#
A top rated company will host all kinds of transfer switches and that too of optimal quality. Be it an automatic transfer switch for places sensitive to power supply breakdown or manual switches for your residence, you will find units which are 100% reliable and long lasting.

Furthermore, you should also come across both ABB single phase as well as 3 phase N units with price inclusive of taxes.

# Should Consist Of A Comprehensive Selection Of ATS And Manual Transfer Switch Units…#
Along with incorporating both categories of transfer switches, next you need to check if the agency holds different variants of those units. Top rated dealers in the UK will always have a vast extension of 3 – 4 pole ATS/MTSs.

Also, for ATS, the best agencies will host units ranging in power amp from 25 to 2500.  For MTS, amp range available for you will be around 16 to 2000.

# Lastly All Transfer Switches Should Be from The Best Names In The Industry…#
Names such as ‘Lovato Electric, Bespoke, ABB, ICG, DSE’ etc. categorise as the top brands in the market. With due honesty, you would actually look to purchase your ATS/MTS from these brands. The best online dealers in the UK will make this task easier for you by indexing you their products at industry standard rates. So, if you come across an agency which thumbnails transfer switch units of these names, you can go ahead with them and build a long-term relationship.  

These are some sure-fire suggestions you can use to sort out a reliable online store for your purchase. Use these tips, bring home one of these transfer switches and ‘Let There Always Be Light…!’

Want to share something? Use our comment section below and post your feeds freely!

Should You Buy Used Generators in the UK or Purchase New Ones?

You must be thinking:

“Used means less on the pocket but new means the best and I’m getting both of these together.”

Well, you’re right to some extent but not to the whole of it. Why is it that everyone thinks used objects will blow up or what not? Well, if it’s a 20-year-old rust bucket, it won’t work in the first place. That said, buying second-hand has its perks, a lot of them other than just saving up.

Or will it be better to buy a new one?

When to buy used generators in the UK?
If it’s a residential setup, that too, a small one. If your living space is all about the bare essentials even including an AC, then you can opt for a second-hand one. Why?

Firstly, it’s cheaper by quite a few dimes.

Secondly, you don’t need it to be top-end at all. 

Lastly, there are some reliable portals which provide second-hand generators online. Nice right?

How about new generators for sale in the UK?
Bigger your setup, more power it will need. That’s plain old common sense. Buying a new generator means you are investing in a backup power source for a long time, for the future. It is even more vital if you have a commercial setup to power. 

Make a proper choice. You know the best brands, top-end features, guarantees and so on.

Want a proper tip?

Look for chaps who can give you both. If they can offer that, they’ll give you top offers too. Till then, let others with a similar query have this answer. Remember to share this with them.

Are You Using Your Emergency Power System Properly?

The power’s out. You were just about to watch Dany getting Snow-owned (Didn’t happen though…Sigh) and the world is dark and full of terrors. Enough with GoT and that darned-dumb emergency power machine-like-thingy in the basement! Speaking of the basement, you still think if you want to go down there or not. Here’s one single DIY which can make your life a whole lot better.

One Automatic Transfer Switch:

 
For every single time, the power goes out of the window; you’ll hear your grumpy old neighbor swearing sailor chants. Why? Well, your lights will not go out at all. ATS or Automatic Transfer Switch will save your stairway to hell.

They are quite simple actually. It’s just a box, nothing fancy.

DDIY (Don’t DIY! Duh!) – This is one of those highly intelligent ‘Don’t do this at Home’ things. So, don’t try installing this single-handedly; leave it to your electrician.

You install one right onto your electrical setup; preferably on the main supply wiring close to your backup generator.

Why install an ATS with emergency power systems?
So that, you don’t notice the power going out. If your backup generator does work, what this magic switch will do is, well, Switch. It will automatically start drawing power from your backup generator.

Now, here’s a bit more. There are different types of ATS available on the market. If you want just the basic power-never-runs-out thing, just get CTTS (Closed Transition Transfer Switch) or OTTS (Open Transition Transfer Switch). If, you want something state-of-the-art, go for an STS (Soft Loading Transfer Switch). What’s that?

Well, just imagine it as a perfect safety for more than just power cuts, but voltage drops too.
Enough said. Buy one.

Things to Consider when Buying New Generators for your Business

In the recent times, we have seen an increase in the price of retail price of electricity. Thus, many business owners have considered buying new generators so that they can supply power for the functioning of the business. This reduces the regular cost of electricity, but one lump sum investment needs to be made. Besides reducing the per month electricity cost, the generators also plays a very crucial role in being the emergency supplier of power in cases of power outages.

Things to Remember
Before finally buying the generator, you should always keep a few things in mind so that you buy the best one that ideally suits your business. The points to remember are as mentioned below –

• At the very beginning, a proper planning of the budget is of extreme importance to decide how much you can afford to pay for the generator without affecting the business. This is necessary to prevent any problematic situation in the future.

• Next, you need to decide what power output is expected from the generator which will be a great help when the generator is to be bought. You should choose the appropriate one as per your requirements

• Then you should have a fair idea about the overall cost of implementation of the generator which would be an addition to the price of the generator and hence should always be kept in mind.

• You should have a clear understanding of the cost of fuelling the generator itself which is again an additional cost that has to be borne.

• Finally, you should check for the durability and the longevity of the generator.

Thus, before making the final purchase of the generator, you should consider the points mentioned above to select the ideal one for your business and to make the most of it.

Implementing an Emergency Power System Successfully

Emergency power systems are today installed in almost all commercial places and facilities in numerous capacities. However, there is various queries and confusion in the mind of any person who is installing it these systems. Below we clear some common confusion that plagues the mind of any customer regarding these emergency power supply systems.

Cost of implementing these systems
This is inadvertently the first thought that plagues the mind of any customer. The implementation cost of these systems depends on various factors like its voltage capacity, the length of construction required for its installation, type of technology, etc. For instance, a high tech, high voltage system would cost more than a low tech low voltage system.

Cost of fueling the generator
Generators use different types of fuel. Diesel or natural gas is the most common fuel used for generators, but the more sophisticated systems use a Bi-fuel system which runs partially on diesel and partially on natural gas which is the more expensive one of the two. Again the amount of power as well as the duration for which standby power is used also impacts the amount of fuel consumed. Thus the cost can be appropriately calculated.

Longevity of generators
Whether you are looking to buy a residential generator or a commercial one, durability and longevity are essential considerations. Most clients, especially those looking to install the in the commercial spaces want it to last for decades. This implies that one needs to buy a more sophistication and higher quality system which would be on the expensive side. The maintenance cost is another crucial factor to consider.

Understanding Automatic Changeover Switch and its Various uses

There are certain systems and places like data centers and medical hospitals which cannot afford to go for even one second without electricity and need an uninterrupted power supply. Moreover, these units cannot be played havoc with due to electrical issues like low voltage, power surges, spikes, low frequency, etc. However, all these issues can be taken care of easily by installing an automatic changeovers switch with your backup emergency power source.

In scenarios, if a power outage, these automatic transfer switches can automatically shift load circuits to and from the power source in a sage manner and ensure continuous power supply with minimal to no outage. They do not require any human intervention. Acting like voltage monitors, they work almost similar to a thermostat to regulate incoming power and immediately turns up the backup power supply whenever the power falls below the pre-specified value by the user. They can be used for various switches like –

• One generator to another – This type is used in systems where multiple power generators are used to generate backup power supply.
• Utility power to a generator – These are used in facilities that have a utility source as well as an incoming power source and require generators for backup only.
• Utility power to another power – This type of switches is used in systems which have utility feeds on both ends. Such systems can also work quite comfortably in manual switches as well.
• A three-way system – Such a system has two utility sources and one backup generator. These systems are used in extra sensitive areas like jail and military base. These are also known as dual systems.

You can pick the one that best suits your requirements and your budget.

Benefits of Emergency Power System Installation in Your Premises

Emergency power systems supply us with an uninterrupted alternative source of energy during any power outage so that all our gadgets and electrically run units can continue uninterrupted. They give the owners assurance and mental peace that no loss would come to any work due to power supply getting cut off abruptly. Let’s look at some of the main advantages of an emergency power.

• Power outage and blackouts can happen at any point without any warning. This can bring out your business to a standstill and cause severe loss to it. If the computers are storing data, even a second of loss of power supply might equate to an enormous financial loss. At home, it is even difficult to cook food today without a power supply since today our cooking medium; gadgets to prep food and even cleaning of dishes all require electricity. Thus, an uninterrupted power supply becomes mandatory, and these emergency systems fulfill the need beautifully.

• These systems are life-saving in a hospital and doctor’s offices. Without it, critical units like a life ventilator and other life supporting machinery would not work. This can even lead to the death of the patient.

• During any blackout, there is an increased risk of theft and burglary, be it a residential or a commercial premise. Uninterrupted power supply safeguards you from falling prey to such unfortunate incidents.

The backup power systems are installed and connected to the main utility system such that they would start automatically by themselves in the scenario of a power outage or you can turn it on manually within a couple of minutes. Thus, you need not hassle about getting it work.

Learn the Working of Transfer Switch System and an Automatic Generator

We all are dependent on electricity. Almost all our actions and the things that we use require electricity for their proper execution.  However, all our work comes to a halt when the electricity goes out. That is where generator helps in providing constant electricity supply to us. An automatic generator and a transfer switch system work in a way to automatically transfer electricity to the required site.  

Working of a Control System inside the Automatic Transfer Switch
When the main electricity source fails to work, then the power generated from a used or new generator is manually or automatically directed to that place. This ensures constant power supply to the site. This work is accomplished through an automatic and manual transfer switch.

How does an automatic transfer switch differ from an automatic transfer work?
It is the control panel system located within the transfer switch that makes it either manual or automatic in nature.

Manual switch
These types of switches are operated by personnel present onsite. They are used in those circumstances where the nature of the load is not critical.

Automatic transfer switch
These types of switches detect power failures on an immediate basis and lead to seamless conversion of utility power into generator power. As soon as the generator comes to the desired frequency and voltage, control system present inside automatic load transfer switch signals the transfer switch to perform the transfer of electricity from the normal electricity source to the generator.

In this way, a transfer switch assists in redistribution of power from the grid to the backup electricity source. It's efficient working mechanism eases our work by giving us uninterrupted power supply at all times. 

Generator - The Best Solution during the Situation of Power Outages

A sudden disruption in electricity can cause so many disturbances in our day to day activities. The generator is one of the electronic equipment that helps in maintaining the power supply when the power supply cuts off. When buying it, you need to take care of its certain aspects that will help you get the right one for your needs.

Learn about the power requirements

To buy a new generator, you need to identify your actual wattage requirement of your house. There are wattage calculators available online that gives you a precise calculation of the power rating of most appliances that you use at your home.

Choose the right model

Like other electronic devices that are available in different models, new or used generators are also available in 2 ways i.e., a stationary model, or a portable generator. 

Stationary Generators

This type of generator is expensive and need a specialized person to install them. They start automatically in event of power cut off. They often provide more amount of electricity to the place. Generator switchgear performs a self-diagnosis to learn the need of their maintenance. They intimate you about it by sending an email.

Portable Generators

In UK, there are several electronic companies that give you best quality generator at the most competitive price. A portable generator is an affordable option when you choose to buy used generators UK. They are a gas powered generator that requires stabilizer for storage of fuel. 

Choosing the right generator and performing its installation in the right way would give you immense benefits. 

Buying a Used Generator Means Value For Money

Industrial generators are usually rugged and will work for decades. After that, the engine can be reconditioned and the unit works like new provided the alternator coils have not been subjected to excess loading. This is not the only issue with buying used generators. Consider these tips and make an informed buying decision.

Background of the generator

If it is possible find out how much the generator was used before it was disposed off. Most industries buy new generators and keep them in standby mode whereas some may have made continuous use of the system as a prime power source. Look at the age, hours of use, make and model and its condition. 

Buy through a generator selling company

Instead of buying used generators directly, it is advisable to buy from a seller who purchases and refurbishes generators. They carry out a thorough check of the engine, carry out repairs where necessary and then put it through tests to ensure the engine works as good as new. They also check the alternator unit coils and the generator switchgear, carrying out repairs or replacement as may be necessary. He will also inspect and replace bearings and bushings. You pay a slightly higher price but far lower than what you would pay for a new unit yet get a generator that is as good as new and just as dependable.

Load test

A seller may claim the new or used generator is best performing one. Insist on a load test and even overload the generator by 25% to see how much it heats up. A dealer specialising in new and used generators will gladly offer this test to give full satisfaction. The generator he sells will carry a full guarantee, giving additional peace of mind.

Buy only after these checks and from a seller who can offer maintenance support.